Vcds Interface Not Found
This article show a guide on how to configure VCDS diagnostic cable for you laptop
- Ross Tech Usb Interface
- Vcds Interface Not Found Windows 7
- Vcds Interface Not Found
- Vcds Interface Not Found Windows 10
- Vcds Interface Not Found 12.12
Preparation:
Procedures:
Connect the USB end of your USB Interface or the Serial end of your Serial Interface to the correct port on your PC. If your PC is further from the vehicle’s diagnostic port than 6 feet,
connect an approved Extension Cable between the PC and the Interface.
How to fix a failed firmware update (flashing red LEDs) on a current generation Ross-Tech® VCDS® interface - the HEX-V2® and HEX-NET®.Brought to you by Genda. STEP 3: Disable Internet & Launch VCDS Software. Golden Rule: Must disconnect from internet everytime before launching VCDS, else will say 'Interface not found'. Also, do NOT update the software. Read golden rule above? Launch VCDS software from Start Menu. Or from C: Ross-Tech VCDS VCDS.exe. Go to: Options » Test (leave it as USB). The port shows up. But the interface not found. Ive tried doing this while connected to my s4. I have tried uninstalling, and reinstalling multiple times. Fire wall is off. I don’t mind being out $10.00 for the cable. But looking for suggestions before I bite the bullet on full version with the Ross tech cable.
If you are using a Serial Interface then you can proceed to step #4. If you are using a USB
Interface, a message like this should pop up:
The drivers many install automatically in Windows 7 or Vista. If you are using XP or W2000, click on the Found New Hardware message and the Found New Hardware Wizard should start up. If you are prompted with the choice, pick “No, Not This Time” when asked if you want to connect to the Internet to search for drivers. Select “Install the software automatically (Recommended)” then click [Next >]
The process should be automated but you may need to click “Continue Anyway” part way through the process.
If, for some reason, you installed the USB Interface without following the above instructions, and VCDS does not work correctly, go into your PC’s Device Manager while the USB Interface is connected.
You can find the Device Manager by right-clicking on My Computer in XP or on Computer in Vista or 7. Select Manage to bring up Computer Management. On the left side of the screen under System Tools, select Device Manager.
Find the “VCDS Compatible USB Interface” or similar and delete it. It may be under “Other Devices” or under “Universal Serial Bus Controllers”. Next, unplug the USB Interface from your PC, wait 5 seconds and plug it back in.
Connect the car end of your Interface to your vehicle’s Diagnostic Port.
If your vehicle has a 2×2 port (some pre-1996 vehicles), then use the optional 2×2 Adapter between the Interface and the ports in the car. This is included in the Pro-Kit.
Turn the vehicle’s ignition switch to the ON position. Make sure the key is turned far enough that the dash lights are fully illuminated. The engine may either be running or stopped.
Start the VCDS program on your PC through either the Start Menu or the VCDS icon on your Desktop.
Ross Tech Usb Interface
From the Main Screen in VCDS click the [Options] button to go into the Options screen.
Once you are in the Options Screen,Select the correct port for your PC’s USB Port (USB) or Serial Port (typically COM1 or COM2) and click the [Test] button. Ensure that VCDS finds your interface.
You should see a message like this:
If the Interface Status is “Not Found!”,check the connections at the car and PC.Make sure both are plugged in securely.Serial Interfaces get their power from the vehicle so they will not be recognized at all if not plugged into a car.
Adapter Type should always be “RossTech” followed by the name of the Interface such as “HEX-USB+CAN”.
Version indicates the firmware version of your Interface. It may be updated by new versions of VCDS, if so follow the prompts on the screen.
Once you have tested successfully, click [OK] then click [Save] to apply this configuration,you will be returned to the Main Screen. Click on [Select] to view the Select Control Module Screen. Select one of your car’s Control Modules such as Engine.
Note: Your car will not have all the Control Modules listed in VCDS, only the functional ones that were installed in your vehicle.
After VCDS has connected, click on [Fault Codes] to check for Fault Codes (DTCs).Repeat the process for each of your car’s Control Modules.
VAG COM 12.12 Interface Not Found Problem Solution Share From ebdtool.com
Problem may caused by:
VAG COM 12.12 interface vcds 12.12 software connect to internet after installation, and caused driver updated
Solution:
Uninstall all related software, and download the software below. And reinstall the software
Software Download Link
https://mega.nz/#!tJlXjLra!RJq9ND8Bi4wlMcn8orLSUNVn_TaxV4F-U-lZP68APT8
Vcds Interface Not Found Windows 7
Attention:
1.Computer time into 2013.10.1 (each software prompts to change the system time expired are to this time), turn off all network connections.
2.Please never connect it to Internet and update the software.
3.To avoid loss and damage of software data,please dont pull up and plug USB and OBD port during the use(open the software and communications within car).
4.Please make sure all the antivirus programs are closed before using,it is very important. Drivers path: C:Ross-TechVCDS If need password, the password is xxxROSSTECH
Cable Status Screencut
1.Cable connect to computer but not power on
Vcds Interface Not Found
2.Cable connect to computer and power on
Vcds Interface Not Found Windows 10
3.Cable connect to computer and connect with car
Vcds Interface Not Found 12.12
More question about VAG COM 12.12, just keep your order number contact with Skype: eobdtool02